Keep drive spinning mac os x4/10/2023 ![]() Mirroring Apple's recommendations, we recommend that you choose APFS if your destination device is an SSD and will be used to back up macOS, or if you are backing up a T2-based Mac and you intend to enable encryption on the backup. High Sierra: both APFS and Mac OS Extended (Journaled) are acceptable formats for a backup of the system. You can encrypt your backup by enabling FileVault while booted from the backup volume. If you are making a backup of a Big Sur or Catalina startup disk, you should create a Data-only backup to avoid the conversion of the destination filesystem to APFS.īig Sur, Catalina, and Mojave: Choose APFS if you are backing up your startup disk or another installation of macOS. You can format these devices as APFS and try to make a bootable backup, but if the performance of the device is too slow to be practical, then we recommend you choose Mac OS Extended (Journaled) for the format. "Slim" backup devices, 2.5" disks) APFS is not designed for these devices, macOS boot performance may be poor. If your destination device is an HDD with a rotational speed of 5400RPM (or slower): (e.g. Choosing a Format for your destination volume If you do not see the Scheme option, go back two steps and select the whole disk device, not one of the volumes on the disk. You can set the name to whatever you like, but set the Scheme to GUID Partition Map. Erase the specified diskĬlick on the Erase button in Disk Utility's toolbar, then configure the name, format, and partitioning scheme of your disk. Click the Eject button next to any volumes on the disk to preemptively unmount them before erasing the disk. because Spotlight prevents the unmount request). Unmount any volumes on the specified diskĭisk Utility occasionally has problems with unmounting a volume while attempting to erase it (e.g. If your disk is a Fusion device, you may erase the "container" within it instead. You must select the whole disk to correctly initialize the device. Please pay particular attention to selecting the disk, not one of the volumes on the disk. A startup disk will often include the manufacturer's serial number in the title (e.g. The name of a new disk will often include the manufacturer’s name (e.g. This disk should not be the same as your startup disk. Before doing anything else in Disk Utility, choose Show All Devices from the View menu, or from the View popup button in Disk Utility's toolbar.Ĭlick to select the disk that you would like to use as the destination for your CCC task. Unfortunately, this hides the devices that you need to select to modify the partitioning of your backup disk. Watch a video of this tutorial on YouTube Show All Devicesĭisk Utility offers a very simplified view of your devices by default. Instructions for Big Sur, Catalina, Mojave, and High Sierra macOS 10.12 Sierra and OS X 10.11 El Capitan.macOS 11Big Sur, 10.15 Catalina, 10.14 Mojave, and 10.13 High Sierra. ![]() Choose About This Mac from the Apple menu to determine your current OS, then make a selection below. is moving around or putting papers down.The remaining steps vary considerably depending on the operating system you are running. The only other likely cause is a loose cable, which if your using a laptop is more likely as the cable is in a location nearer to where your hand etc. Power is definitely the most common cause of problems but this should not apply to external 3.5" hard disks since they all come with their own dedicated power adapters. However if you tried to use more than two FireWire drives at the same time then you are again in danger of exeeding the power available. Normally, a 2.5" external FireWire drive would not have a problem since as I mentioned above FireWire has more power to start with. This allows it to draw power via two USB cables at the same time in theory giving it twice as much power and thus solving the problem.Īs another reply pointed out, some ports on the Mac may share the same USB bus and hence share the same limited power allocation. A lot of these drives come with a special USB cable that connects to the power input socket on the hard disk to be used in addition to the normal USB data cable. SATA drives need more power than PATA drives, so an external SATA 2.5" drive which draws power for itself from the USB port is borderline as to whether it will work. This is because USB ports on all computers provide less power than a FireWire port. Using a USB hard drive on a Mac will often result in intermittent disconnection or a failure to connect at all in the first place.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |